Filter by price
Recently viewed products
Arduino Shields
Add communication, motor control, power and interface functions to Arduino projects with compatible expansion shields.
Control Board Ramps 1.4
It is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in for stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.This board is mostly based on Adrian's Pololu_Electronics and work by Tonok. Copper etch resists methods suggested by Vik. Also inspired by Vik's work with EasyDrivers. circuit design based mostly on Adrian's Pololu_Electronics Joaz at RepRapSource.com supplied initial pin definitions and many design improvements. Much inspiration, suggestions, and ideas from Prusajr, Kliment, Maxbots, Rick, and many others in the RepRap community.
Control Board Ramps 1.5 for 3D Printer
powered outputs. Power and Thermistor Support for 2nd Extruder. Heated bed c3 PWM controlled MOSFETontrol with 11A fuse 3 thermistor circuits, 2x Extruder, 1x heatbed. 5 stepstick Stepper Driver sockets 6 sets of Digital Pins in headers with VCC and GND for endstops Extra pins broke out : PWM, digital, serial, SPI, I2C and analog Supports Bluetooth and SD card add on upgrades support: A4988 DRV8825 and other motor drivers Input voltage: 12V Power: 200W Brand : Arduino Type : 3D Printer Accessories
Control Board Ramps 1.6 for 3D Printer
RAMPS 1.6 interface board with new, more powerful SMT MOSFET drivers Improved heat dissipation with new heat sink，the PCB has a built-in selection terminal for driving the SPI working mode, and is compatible with STEP/DIR and SPI modes The power supply and hot bed use 30A high-current terminal block, to avoid the situation of burning terminals to a greater extent Added a reset expansion interface, convenient for users to extend the reset button, X, Y, Z, E0, E1 all use parallel dual motor interface, so that the board is suitable for more models Design of plate pin socket can be easily replaced or removed for future design, Changed the silk screen, making the wiring clear at a glance. Using a combination of colored pin headers and mothers, effectively distinguishing each functional interface, both beautiful and practical
Sensor Shield v2 for arduino Mega 1280 or 2560
The Sensor Shield v2 is an advanced expansion board engineered for seamless integration with Arduino Mega 1280 or 2560 control boards, greatly enhancing connectivity and prototyping efficiency for complex electronic projects. This versatile board is designed to provide a straightforward and reliable interface for a wide array of sensors, servos, LCDs, and other modules—ideal for makers and professionals seeking robust development solutions.
Double-side PCB Prototype Screw Terminal Block Shield Board Kit For Arduino Mega 2560
Prototype Screw/Terminal Block Shield Board Kit For ArduinoMEGA-2560 R3.
Arduino Prototyping Prototype Shield ProtoShield With Mini Breadboard
ARDUINO PROTOTYPING PROTOTYPE SHIELD WITH BREADBOARD 170 POINTS ALL ARDUINO PINS ARE BROUGHT TO THE TOP LEVEL. 1 RESET BUTTON, 1 GENERAL USE BUTTON, AND 2 LED CIRCUITS CAN BE USED DIRECTLY. 5V, GND, AND RAW PINS ARE EXPOSED AS WELL. SOIC PLACE FOR IC. THE MINI BREADBOARD HAS 170 TIE POINTS. THE BREADBOARD STICKS ON THE PROTOTYPE SHIELD WITH ITS SELF-ADHESIVE BACKING. PROTOTYPE SIZE: 7CM X 5.5CM X 2CM MINI BREADBOARD SIZE: 4.4 X 3.4 X 1CM PACKAGE INCLUDES: 1X ARDUINO PROTOTYPE SHIELD 1X MINI BREADBOARD 170 POINTS
Arduino UNO Sensor Shield V5
The Arduino Sensor Shield V5 is an add-on board designed for the Arduino microcontroller platform. It provides a convenient way to interface with various sensors and actuators, allowing you to quickly prototype and build projects that involve sensing and controlling the physical world.
Joystick Shield for Arduino
The SparkFun Joystick Shield Kit contains all the parts you need to enable your Arduino with a joystick! The shield sits on top of your Arduino and turns it into a simple controller. Five momentary push buttons (4+ joystick select button) and a two-axis thumb joystick gives your Arduino functionality on the level of old Nintendo controllers. Soldering is required, but it’s relatively easy and requires minimal tools.
Arduino RTC / SD Logger Shield
The Arduino RTC / SD Logger Shield is a module that allows you to store data on an SD card and keep track of time with a real time clock. It is ideal for data logging projects that require accurate timestamps and reliable data storage.
NANO 3.0 controller Terminal Adapter for NANO Arduino
NANO 3.0 controller Terminal Adapter for NANO terminal expansion board for arduino Nano version 3.0 in stock
Arduino Nano CNC Shield V4 & 3 Channel A4988 Stepper Driver
3D printer stepper motor driver CNC shield V4 needs to work with Nano board. It can be used as driver expansion board for engraving machines and 3D printers. It has in total 3 channel slots for A4988 stepper motor driver modules (not included) for driving 3 channel of stepper motors. Each channel of stepper motor only needs 2 IO ports, which means 6 IO ports is sufficient to manage 3 stepper motors. This shield can make quick work for managing stepper motors in your projec
Arduino Motor Shield 4 Channel L293D H-Bridge Dc Motor Control Support PWM
Flux L293D Shield can use DC motors and power supplies of up to 36 Volts, can supply a maximum current of 600mA per channel, the L293D chip is also a H-Bridge. - 2 interface for 5V Servo connected to for Arduino's high-resolution dedicated timer. - Can drive 4 DC motors or 2 stepper motors or 2 Servo - Up to 4 bi-directional DC motors with individual 8-bit speed selection - Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. - 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC - Pull down resistors keep motors disabled during power-up - Reset Button - 2 external terminal power interface, for seperate logic/motor supplies - Tested compatible for Arduino UNO, Mega, Diecimila & Duemilanove