Products tagged with 'module'

View as Grid List
Sort by
Display per page

12V LED Automatic Control Switch Relay Module

03.00.45
12V LED Automatic Control Switch Relay Module Features: Practical and long service life. Increase the supply anti-reverse function. Use opto isolated input and output, enhanced anti-jamming capabilit consumption. Set parameter after power for perdurable memories. Signal terminal voltage signal can be maintained for a longtime. Different working mode selections. Working mode: Working mode selection: After power on – long press K1 for 2 seconds later into the select function mode, P1-1 to P1-4 for choose. P1-1 operating modes: a signal to trigger relay, time is up, the relay disconnect users, You can set relay time T, click K2 the hundred digital tube starts flashing, then press K3, the hundred digital change; click K2 ten digital tube starts flashing, then press K3, ten digit changes; click K2 bit digital tube starts flashing, then press K3, single-digit change; then click K2, digital pipe does not blink, then press the K3, shifting the decimal point, the decimal point in a bit indicates 0-999 minutesin ten represents 0 to 99.9 seconds without a decimal pointrepresents 0-999 seconds; goodchoice, bringing the time setting is completed. Short press K1, enterfunction offine-tuning settings, triggerthedefaultdelayperiod is invalid, press K1, during the delay trigger active(re-timing),clickon the K1, during the delay reset (timer turned off, the relay reset) press again to repeat the default settings for the first time. P1-2 operating modes: Asignal trigger , digital countdown begins,X seconds after, there lay open Y seconds, then close.Users can set the relay time X, Y ; P1-1different time settings similar to the blue lights that set the relay time, blue light indicates setting relay off time. Short press K1, enter function offine-tuning the set, the default trigger is invalid during the delay, pressK1, during the delay trigger active(re-timing), then click the first repeat default settings. P1-3 operating modes: Open X seconds, disconnect Yseconds, infinite loop. Users can set the relay timeX , Y ; time setting similar to P1-2.Short press K1, enter function offine-tuning set, The default function is: set up an electric circuit the relay first open, press the K1, there lay first close. Press again to repeat the default functionality. P1-4 operating modes: a signal to trigger the relay open but do not start the timer,when the trigger signal disappears, digital count down begins, X time after, the relayclose; During the delay, again to the signal,digital count down canceled, stays energized, the signal disappears, restart count down; (equivalentto release the button to start timing, commonly used in power-offdelay).Users canset the relay time X; time setting similar to P1-1. Specification: Size: 64.2mm x 34.8mm x 18.5mm Relay Specifications: AC 220V 10A or DC 30V 10A. Quiescent Current: 20mA,Operating Current: 50mA. Working voltage: 10~16V (if other ranges can be customized). Signal voltage: 4V~20V (if other ranges can be customized). Life: about100,000times,Working temperature:-40~85'C.
250.00 ج.م.‏ 210.00 ج.م.‏

AC-DC 5V700mA 3.5W Power Supply Buck Converter Step Down Module

03.00.28
Type : Electronic Accessories Output Over Power Protection Short circuit protection Temperature protection Current protection Dimensions:3cm x 2cm x 1.8cm
80.00 ج.م.‏ 70.00 ج.م.‏

Arduino Pyroelectric Infrared IR PIR Motion Sensor Detection Module

03.00.101
Arduino Pyroelectric Infrared IR PIR Motion Sensor Detection Module This is a highly integrated module popularly used for entry detection, it can simplely and easily to adopt in system. There are two adjustable potentiometer on the module, you can use them to change the trigger sensitivity and the duration of the trigger signal. This is a highly integrated module popularly used for entry detection, it can simplely and easily to adopt in system. There are two adjustable potentiometer on the module, you can use them to change the trigger sensitivity and the duration of the trigger signal. Specification : Input Voltage: DC 4.5-20V Static current: 50uA Output signal: 0,3V or 5V (Output high when motion detected) Sentry Angle: 110 degree Sentry Distance: max 7 m Shunt for setting override trigger: H - Yes, L - No
80.00 ج.م.‏ 60.00 ج.م.‏

Bigtreetech New 3D printer hot bed Power expansion board/Heatbed power module/MOS tube high current load module for 3D printer

03.00.67
*Completely solve the hot bed power is too large and the load current issue *Under the premise of normal cooling, it work stable under I(Max)=10A, the current must not exceed 10A while the process working *If you need anything greater or equal to 10A this module is a must! For example, if your total power usage is 120W and you have 12V power supply, then it means at least 10A is needed (10X12=120W). *As ChiTu controller board is only capable of 10A this setting will not work. To make it work,you need this extra power module. *If the power is used improperly, it may burn. *Dimensions: 60*50mm
200.00 ج.م.‏ 175.00 ج.م.‏

Bluetooth Module HC-05 , Serial TTL

03.00.44
The HC-05 is a class 2 Bluetooth module designed for transparent wireless serial communication. It is pre-configured as a slave Bluetooth device. Once it is paired to a master Bluetooth device such as PC, smartphone and tablet, its operation becomes transparent to the user. No user code specific to the Bluetooth module is needed at all in the user-microcontroller program.
200.00 ج.م.‏ 175.00 ج.م.‏

Bluetooth Module HC-06 , Serial TTL

03.00.33
Bluetooth UART RS232 serial converter Module Operating Frequency Band 2.4GHz unlicensed ISM band Bluetooth Specification V2.0+EDR Output Power Class 2 Operating Voltage 3.3V Host Interface USB/UART Audio Interface None Flash Memory Size 8Mbit. Features: CSR Bluetooth Chip Solution Bluetooth v2.0+EDR Compliant UART interface and with baud rate setup function Built-in antenna. Coverage up to 30ft. Incredible small size with 3.3V input, and RoHS Compliant Working current: While pairing 30mA, paired 8mA Frequency: 2.4GHz ISM band Baud rate is 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 user manually set up. Default Baud Rate: 9600,8,1,n Support for 8Mbit External Flash Onboard Support for 802.11 Co-Existence Product Description Storage Temperature: -40 to 85 degrees Celsius Size : 28 mm x 15 mm x 2.35 mm Used for GPS navigation system, water and electricity gas Automatic Reading Meter, The industrial field in control system The factory default parameters: Baud rate: 9600, N, 8, 1. Pairing code: 1234 AT command set as follows: 1, Test communication Send: AT (return OK, A seconds press once again) Return: OK 2, Change Bluetooth serial interface communication baud rate Send: AT + BAUD1 Return: OK1200 Send: AT + BAUD2 Return: OK2400 1---------1200 2---------2400 3---------4800 4---------9600 5---------19200 6---------38400 7---------57600 8---------115200 9---------230400 A---------460800 B---------921600 C---------1382400 Not recommended in more than 115200 baud rate, the signal interference will make the system not stability 3, change bluetooth name Send: AT + NAMEname Return: OKname Parameter name: will set the current name, which was the name of the search to Bluetooth. Within 20 characters. Example: send AT + NAME bill_gates Back to OKname now Bluetooth name is bill_gates Parameters can power lost save, modify it only need once. The PAD service can see change Bluetooth name 4, Change Bluetooth pairing password Send: AT + PINxxxx Return: OKsetpin Example: send AT + PIN8888 Back to OKsetpin now Bluetooth pairing password is 8888, module's default password g is 1234. Parameters can power lost save, modify it only need once.
210.00 ج.م.‏ 185.00 ج.م.‏

Broken Filament Wire Monitoring Trigger Sensor Switch Module

03.00.103
How it works: The material detection module uses the level jump detection method: When there is material, the detection level level signal should be high level, no material, the material port level signal becomes low level, the system detects a certain high Level to low level of the jump, then that the material exhausted, the implementation of the suspension of the order, waiting for the replacement of good material after the implementation of continuous printing. Features: Feeding mouth and outlet at the same time to increase a wear-resistant copper sets. Can effectively extend the product life.
120.00 ج.م.‏ 100.00 ج.م.‏

Dual H Bridge DC Stepper Motor Controller L298N Module for Arduino / Due and Raspberry Pi

03.00.25
Type : 3D Printer Accessories Brand : Other
130.00 ج.م.‏ 100.00 ج.م.‏

Ethernet LAN Network Module ENC28J60 For Arduino SPI AVR PIC LPC STM32

03.00.22
Description: Chip board ENC28J60-I/SO. The board 25MHZ crystal. The network interface board HR911105A. 3.3 V power supply pin Specifications: Net weight:15 g Package weight:25 g Color:Blue Package Included: 1 x New ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC STM32
150.00 ج.م.‏ 130.00 ج.م.‏

Gy-521 Mpu-6050 Mpu6050 Module 3 Axis Analog Gyro Sensors 3 Axis Accelerometer Module For Arduino

03.00.52
Name: MPU-6050 modules (three-axis gyroscope three-axis accelerometer) compatble with Arduino Use the chip: MPU-6050 Power supply :3-5v (internal low dropout regulator) Communication modes: standard IIC communications protocol Chip built-in 16bit AD converter, 16-bit data output
95.00 ج.م.‏

Heartbeat Sensor Module KY039

03.00.93
Brand : Other Type : Electronic Accessorie
75.00 ج.م.‏ 60.00 ج.م.‏

High Power LED Module "Power 3W"

03.00.107
Color temperature: Warm White 3000-3200K / white 6000-6500K Forward current: 700MA Luminous flux: White 180-200LM (lumens) Forward voltage: 3.3 - 3.6 V Reverse voltage: 5V Power: 3W Viewing angle: 180° Working temperature: -20° to 60° Brand : Other
45.00 ج.م.‏

HITSAN MKS-LV8729-OC Stepper Motor Driver Module High Subdivision One Piece

03.00.35
M CREATE A LV8729 MBASE MAKER (M), A SUPER QUIET REST, SUPPORTS EN +/-INPUT. MLV8729 DC SUPPLIES 9-32 VOLTS, AND GOOD FOR NIMA THE OTHER ENGINES THAT CURRENTLY HAVE LESS THAN 1.5 A. THESE CONTROLS MICROSTEP THE DRIVER BY THE CURRENT DIGITAL LOOP, MAKING THE ENGINE STATIONARY, QUIET AND ACCURATE. MLV8729 DOES GOOD WORK WITH THE GENERAL M, MSBASE AND RAMPS1.4 OBSERVER BOARD ON 3D PRINTER, MACHINE SCULPTING, CNC, ETC. FEATURES 1. DC 9-32 VOLTS, IT IS BETTER TO SUPPLY DC12V OR DC24V. 2. USE HIGH SPEED OPTOCOUPLER, DO NOT LOSE STEP. 3. USE THE SANYO LV8729, WHICH PROTECTS THE CIRCUIT AND SUPPORTS 128 MICROSTEP. 4. CURRENT MAX: 1.5 A. 5. MICROSTEP: 16/32/64/128. 6. GREATER HEAT SINK, BETTER COOLING. NOTICE 1. PLEASE MIND THE POLAR POWER, OR ELSE IT WILL BURN THE CHIP. 2. IT IS BETTER TO ADJUST THE CURRENT UNDER THE CURRENT CLASSIFICATION OF THE ENGINE, THE CURRENT ADVISES LESS THAN 1A. FOR THE MEGA2560 CONTROL, ADVICE NO MORE 64 MICROSTEP. 3. SWITCH1, 2 RECHARGEABLE MICROSTEP, SWITCH3, 4.5, USED FOR CURRENT, THE SWITCH6 ENTRY IS PLACED.
250.00 ج.م.‏

Infrared Receiver Module KSM803

04.00.139
KSM-803LM Optical Receiver Module With high quality (MADE IN TAIWAN). The KSM-803LM consist of a PIN Photodiode of high speed and a preamplifier IC in the package as an receiver for Infrared remote control systems
30.00 ج.م.‏ 15.00 ج.م.‏

IR Flame Sensor Module 4 pin

03.00.111
Can detect flame or wavelength of light source within 760nm~1100nm Lighter flame detect distance 80cm
40.00 ج.م.‏

ISD1820 Voice Recording Recorder Module With Mic Sound Audio Loudspeaker Diy RC Toy Kit Electroincs Develop

03.00.36
Voice Recording MODULE Brand : Other Type : Microcontroller Boards
75.00 ج.م.‏

Lithium Battery Charger Module 1A (TP4056)

03.00.106
Brand : Other Type : Electronic Accessories
70.00 ج.م.‏

LM2596HVS DC to DC Adjustable Step Down Buck Converter Power Supply Module

03.00.24
Input voltage range: DC 4.5V to 53V (input voltage must be greater than the output voltage to 1.5V or more high. Could not boost)
70.00 ج.م.‏

MQ-2 Gas Sensor Module "Smoke , Butane & Propane Detection"

03.00.94
The MQ-2 Gas Sensor module is useful for gas leakage detecting in home and industry.It can detect LPG, i-butane, propane, methane ,alcohol, hydrogen and smoke.The module have a built-in variable resistor to adjust the sensitivity of the sensor..Package Include ": 1 x MQ-2 Gas Sensor Module "Smoke , Butane & Propane Detection"
120.00 ج.م.‏ 100.00 ج.م.‏

MQ-3 Alcohol Ethanol Sensor Module Gas Detector Sensor arduino raspberry pi

03.00.95
SIZE: APPROX. 32 X 22 X 27MM MAIN CHIP: LM393, ZYMQ-3 GAS DETECTOR WORKING VOLTAGE: DC 5V WITH SIGNAL OUTPUT INSTRUCTIONS TWO-WAY SIGNAL OUTPUT (TTL LEVEL OUTPUT AND ANALOG OUTPUT) TTL OUTPUT EFFECTIVELY SIGNAL FOR LOW LEVEL(WHEN THE OUTPUT LOW LEVEL SIGNAL LIGHTS, CAN DIRECTLY CONNECTED MICROCOMPUTER) ANALOG OUTPUT 0 ~ 5V VOLTAGE, THE HIGHER THE CONCENTRATION, THE HIGHER THE VOLTAGE HAS A HIGH SENSITIVITY AND GOOD SELECTIVITY HAS LONG SERVICE LIFE AND RELIABLE STABILITY RAPID RESPONSE RECOVERY FEATURES FOR MOTOR VEHICLES AND OTHER PROHIBITION DRUNKEN DRIVERS HOMEWORK PERSONNEL ON-SITE TESTING, ALSO USED IN OTHER PLACES OF ETHANOL VAPOR DETECTION COLOR IS SHOWN AS PICTURES PLS NOTE THAT DUE TO LIGHTING EFFECTS, MONITOR'S BRIGHTNESS/ CONTRAST SETTINGS ETC, THERE COULD BE SOME SLIGHT DIFFERENCES IN THE COLOR TONE OF THE PICTURES AND THE ACTUAL ITEM!
120.00 ج.م.‏ 95.00 ج.م.‏

MQ-7 CO Carbon Monoxide Coal Gas Sensor Module

03.00.97
THIS SENSOR HAS A HIGH SENSITIVITY AND FAST RESPONSE TIME. THE SENSOR'S OUTPUT IS AN ANALOG RESISTANCE. THE DRIVE CIRCUIT IS VERY SIMPLE; ALL YOU NEED TO DO IS POWER THE HEATER COIL WITH 5V, ADD A LOAD RESISTANCE, AND CONNECT THE OUTPUT TO AN ADC.
110.00 ج.م.‏ 95.00 ج.م.‏

Power Supply Module 3.3V 5V For Solderless Bread Board MB102

03.00.46
Brand : Other Type : 3D Printer Accessories
70.00 ج.م.‏ 50.00 ج.م.‏

RC522 RFID Card Reader Module Kit for Arduino

03.00.34
THIS IS THE RFID 13.56 MHZ RFID MODULE BOARD KIT, THE MODULE BOARD THAT USED ON THIS KIT HAS RC522 INTEGRATED CIRCUIT THAT DRIVES THE 13.56 MHZ RADIO FREQUENCY. THE MF RC522 IS A HIGHLY INTEGRATED TRANSMISSION FOR CONTACT-LESS COMMUNICATION THAT RUNS ON 13.56 MHZ IT SUPPORT ALSO THE ISO 14443A/MIFARE MODE LIBRARY. THIS RFID KIT HAS INCLUDED THE S50 RFID CARD AND ID TAG.
190.00 ج.م.‏

Relay Module 4 Channel

03.00.48
THIS IS A 5V 4-CHANNELS RELAY MODULE, IT CAN BE CONTROLLED DIRECTLY BY A WIDE RANGE OF MICROCONTROLLERS SUCH AS ARDUINO, AVR, PIC, ARM AND MSP430.
120.00 ج.م.‏ 100.00 ج.م.‏

Serial Converter TTL UART on CP2102 USB Module Board

03.00.99
CP2102 its high integration, built-in USB2.0 full-speed function controller, USB transceiver, crystal oscillator, EEPROM, and asynchronous serial data bus (UART), supports full-featured modem signals, without any external USB device. CP2102 with other USB-UART adapter circuit works similar to the PC through the driver's USB port into a virtual COM port in order to achieve the purpose of expansion.
115.00 ج.م.‏ 95.00 ج.م.‏

Stepper Motor Driver A3967 Module

03.00.53
Note: Do not connect or disconnect a motor while the driver is energized. This will cause permanent damage to the A3967 IC
85.00 ج.م.‏ 55.00 ج.م.‏

TL -Smoother Kit Addon Module Four 4 Pin For 3D Printer Motor Driver

03.00.55
Tl-Plus Smooth V1.0 Kit Addon Module For 3d Printer Motor Driver Parts 3D PRINTER leTL-Plus Smooth is a module addon for 3D printer stepper motor. The board provides flyback diodes (freewheel diodes) for the motor outputs, so that they are also protected against induction voltages in the motor-free state of the driver. You will have got smoother
105.00 ج.م.‏ 85.00 ج.م.‏

Ultrasonic Distance Measuring Sensor HC-SR04 Module for Arduino

03.00.98
Ultrasonic Distance Measuring Sensor HC-SR04 Module for Arduino
70.00 ج.م.‏ 50.00 ج.م.‏

XL6009E1 DC-DC Adjustable Step-up Boost Power Converter Module Replace

03.00.117
XL6009E1 DC-DC Adjustable Step-up Boost Power Converter Module ReplaceStable and reliableIt can make the output stabilizedSpecifications:Material: Electronic componentsColor: as pic shownModule: approx. 1.69 * 0.83 * 0.51inch / 4.3 * 2.1 * 1.3cmInstallation diameter: approx. 0.12inch / 0.3cmModel: XL6009E1Rectification: Non-Synchronous RectificationInput Range: 3V-32VOutput range: ...
80.00 ج.م.‏