Arduino Modules

View as Grid List
Sort by
Display per page

1 Channel SSR G3MB-202P Solid State Relay Module 240V 2A

03.00.42
This 5V 1 Channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse is based on the Omron G3MB SSR relay which can control up to 2A at 240VAC. This is a 1 Channel SSR relay module which has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed).
ج.م.‏ 70.00 ج.م.‏ 60.00

12V LED Automatic Control Switch Relay Module

03.00.45
12V LED Automatic Control Switch Relay Module Features: Practical and long service life. Increase the supply anti-reverse function. Use opto isolated input and output, enhanced anti-jamming capabilit consumption. Set parameter after power for perdurable memories. Signal terminal voltage signal can be maintained for a longtime. Different working mode selections. Working mode: Working mode selection: After power on – long press K1 for 2 seconds later into the select function mode, P1-1 to P1-4 for choose. P1-1 operating modes: a signal to trigger relay, time is up, the relay disconnect users, You can set relay time T, click K2 the hundred digital tube starts flashing, then press K3, the hundred digital change; click K2 ten digital tube starts flashing, then press K3, ten digit changes; click K2 bit digital tube starts flashing, then press K3, single-digit change; then click K2, digital pipe does not blink, then press the K3, shifting the decimal point, the decimal point in a bit indicates 0-999 minutesin ten represents 0 to 99.9 seconds without a decimal pointrepresents 0-999 seconds; goodchoice, bringing the time setting is completed. Short press K1, enterfunction offine-tuning settings, triggerthedefaultdelayperiod is invalid, press K1, during the delay trigger active(re-timing),clickon the K1, during the delay reset (timer turned off, the relay reset) press again to repeat the default settings for the first time. P1-2 operating modes: Asignal trigger , digital countdown begins,X seconds after, there lay open Y seconds, then close.Users can set the relay time X, Y ; P1-1different time settings similar to the blue lights that set the relay time, blue light indicates setting relay off time. Short press K1, enter function offine-tuning the set, the default trigger is invalid during the delay, pressK1, during the delay trigger active(re-timing), then click the first repeat default settings. P1-3 operating modes: Open X seconds, disconnect Yseconds, infinite loop. Users can set the relay timeX , Y ; time setting similar to P1-2.Short press K1, enter function offine-tuning set, The default function is: set up an electric circuit the relay first open, press the K1, there lay first close. Press again to repeat the default functionality. P1-4 operating modes: a signal to trigger the relay open but do not start the timer,when the trigger signal disappears, digital count down begins, X time after, the relayclose; During the delay, again to the signal,digital count down canceled, stays energized, the signal disappears, restart count down; (equivalentto release the button to start timing, commonly used in power-offdelay).Users canset the relay time X; time setting similar to P1-1. Specification: Size: 64.2mm x 34.8mm x 18.5mm Relay Specifications: AC 220V 10A or DC 30V 10A. Quiescent Current: 20mA,Operating Current: 50mA. Working voltage: 10~16V (if other ranges can be customized). Signal voltage: 4V~20V (if other ranges can be customized). Life: about100,000times,Working temperature:-40~85'C.
ج.م.‏ 250.00 ج.م.‏ 210.00

150W DC to DC Step UP Boost Converter module

03.00.108
SPECIFICATIONS: INPUT VOLTAGE: DC 10V-32V. OUTPUT VOLTAGE: DC12V-35V(ADJUSTABLE). OUTPUT CURRENT: 5A (MAX). INPUT CURRENT: 8A (MAX) (MORE THAN 8A PLEASE STRENGTHEN HEAT SINK). OUTPUT POWER: NATURAL COOLING 100W (MAX), STRENGTHENING COOLING 150W (MAX) REAL POWER. CONVERSION EFFICIENCY: 94% (WHEN INPUT 19V 2.5A OUTPUT 16V, REFERENCE). OUTPUT RIPPLE: 2% (MAX). WORKING TEMPERATURE: INDUSTRIAL (- 40 ¡Ã C TO 85 ¡Ã C) ( ENVIRONMENTAL TEMPERATURE, MORE THAN 40 DEGREES, PLEASE REDUCE POWER TO USE, OR - ENHANCE COOLING). FULL-LOAD TEMPERATURE: 45 DEGREES. NO-LOAD CURRENT: 25MA TYPICAL. VOLTAGE REGULATION: ¡À 0.5%. LOAD REGULATION: ¡À 0.5%. DYNAMIC RESPONSE SPEED: 200US 5%. SHORT CIRCUIT PROTECTION: NO (PLEASE INSTALLS THE FUSE OR PROTECTION CIRCUIT AT INPUT PARTS). INPUT REVERSE PROTECTION: NO (PLEASE COMPLY WITH A REVERSE PROTECTION OR CONNECT A DIODE AT INPUT PARTS.) SIZE: 65MM X 35MM X 21MM 150W DC to DC Step UP Boost Converter module
ج.م.‏ 130.00 ج.م.‏ 100.00

1-Channels PWM generator XY-LPWM PWM Pulse Wave Frequency Digital Signal Generator Square Wave Duty Cycle Module

03.00.123
1. LCD liquid crystal display frequency and duty cycle, very clear, PWMoutput can be set separately frequency and duty cycle; 2. Wide frequency range and high precision; 3. Serial communication
ج.م.‏ 250.00 ج.م.‏ 225.00

3-way PWM generator XY-LPWM PWM Pulse Wave Frequency Digital Signal Generator Square Wave Duty Cycle Module

03.00.124
Output of three-channel PWMat the same time, Adjustable frequency, 3-channel frequency output consistent, duty ratio can be independently adjusted, suitable for most occasions Lcd can display frequency and duty datio,Easy to oprate; Wide frequency range, high precision; Support Serial operation
ج.م.‏ 300.00

5mW Laser Module emitter - Red Line

03.00.110
Specifications Output Power: Min 2.5mW, Typical 3.0mW, Max 5.0mW Working current: Min 10mA, Typical 20mA, Max 25mA Working voltage: Min 2.3VDC, Typical 4.5VDC, Max 8.0VDC Wavelength: 650nm Working Temperature: Min -15℃, Typical 25℃, Max 35℃ Storage Temperature: Min -20℃, Max +25℃ Focused Dot width:<2mm spotting 3 meters away. Outline Dimension: 12mm(Diameter) x 35mm(Length) Practical test for point head: reflection visible to random target >1000m Cautions: Class III, avoid direct eye exposure to beams.
ج.م.‏ 100.00 ج.م.‏ 85.00

8 Channel Relay Module With Optocoupler for Arduino AVR PIC RPI

03.00.61
This is a 5V 8-Channel Relay interface board be able to control various appliances, and other equipments with large current It can be controlled directly by Micro-controller (Arduino UNO, MEGA, PRO, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)5V 4-Channel Relay interface board, and each one needs 50-60mA Driver Current Equiped with high-current relay, AC250V 10A ; DC30V 10A
ج.م.‏ 160.00

A flexible 4x4 keyboard compatible with Arduino used in electronic locks projects

03.00.78
This is a 4x4 matrix sixteen key membrane switch keypad that is easy to use and will look nice in your project. It has 8 outputs, you should use the “Scan mode” to judge which button has been pressed down. Support in Arduino, AVR, PIC, STM, Raspberry Pi Specification Pad Size: 70 x 77 x 0.8mm Cable Length: 85mm(include connector) Connector: 8 pins female header, 2.54mm Pitch Max Circuit Rating: 35VDC, 100mA Insulation Spe: 100M Ohm, 100V Dielectric Withstand: 250VRms (60Hz, 1min) Contact Bounce: 5ms Life Expectancy: 1 million closures Operation Temperature: Minus 20 to Plus 40 Degree.
ج.م.‏ 40.00 ج.م.‏ 35.00

AC-DC 5V700mA 3.5W Power Supply Buck Converter Step Down Module

03.00.28
Type : Electronic Accessories Output Over Power Protection Short circuit protection Temperature protection Current protection Dimensions:3cm x 2cm x 1.8cm
ج.م.‏ 80.00 ج.م.‏ 70.00

Arduino 30 Amp Sensing & Controlling Current Flow Sensor Module Board

03.00.88
Current Sensor Module 20A range ACS712 The module can measure the positive and negative 20 amps, corresponding to the analog output 100mV / A; 1、The current sensor chips: ACS712ELC-20A ; 2、Pin 5V power supply, on-board power indicator; 3、The module can measure the positive and negative 20 amps, corresponding to the analog output 100mV / A; 4、No test current through the output voltage is VCC / 2; Note: ACS712 is based on the principle of the Hall test, please use this field to avoid impact
ج.م.‏ 120.00 ج.م.‏ 110.00

Arduino and Raspberry Pi 5v Relay Module 1 Channel for Switching Automation

03.00.47
Ideal for single chip microcomputer, household appliance control, etc Control DC / AC signal, can control 220V AC load One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for avoidance of malfunction Power supply indicator lamp Control indicator lamp Channel: 1 channel TTL Control Signal: 5V-12V Relay Voltage: 5V
ج.م.‏ 60.00 ج.م.‏ 40.00

Arduino JoyStick Breakout Module Shield PS2 Joystick Game Controller

03.00.63
Product Description: Tested in: Arduino UNO, MEGA, PRO / Due / Leonardo / Raspberry Pi 1. This is a two-way rocker 10K resistor, with the joystick in a different direction, tap the resistance vary. 2. This module uses a 5V supply, the original state X, Y readout voltage of 2.5V or so. 3. When pressed with the direction of the arrow, the readout voltage values with increasing, up to 5V; press the arrow in the opposite direction, the readout voltage reduction , a minimum of 0V.
ج.م.‏ 100.00 ج.م.‏ 80.00

Arduino Motor Shield 4 Channel L293D H-Bridge Dc Motor Control Support PWM

03.00.77
Flux L293D Shield can use DC motors and power supplies of up to 36 Volts, can supply a maximum current of 600mA per channel, the L293D chip is also a H-Bridge. - 2 interface for 5V Servo connected to for Arduino's high-resolution dedicated timer. - Can drive 4 DC motors or 2 stepper motors or 2 Servo - Up to 4 bi-directional DC motors with individual 8-bit speed selection - Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. - 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC - Pull down resistors keep motors disabled during power-up - Reset Button - 2 external terminal power interface, for seperate logic/motor supplies - Tested compatible for Arduino UNO, Mega, Diecimila & Duemilanove
ج.م.‏ 150.00 ج.م.‏ 120.00

Bigtreetech New 3D printer hot bed Power expansion board/Heatbed power module/MOS tube high current load module for 3D printer

03.00.67
*Completely solve the hot bed power is too large and the load current issue *Under the premise of normal cooling, it work stable under I(Max)=10A, the current must not exceed 10A while the process working *If you need anything greater or equal to 10A this module is a must! For example, if your total power usage is 120W and you have 12V power supply, then it means at least 10A is needed (10X12=120W). *As ChiTu controller board is only capable of 10A this setting will not work. To make it work,you need this extra power module. *If the power is used improperly, it may burn. *Dimensions: 60*50mm
ج.م.‏ 200.00 ج.م.‏ 175.00

Bluetooth Module HC-05 , Serial TTL

03.00.44
The HC-05 is a class 2 Bluetooth module designed for transparent wireless serial communication. It is pre-configured as a slave Bluetooth device. Once it is paired to a master Bluetooth device such as PC, smartphone and tablet, its operation becomes transparent to the user. No user code specific to the Bluetooth module is needed at all in the user-microcontroller program.
ج.م.‏ 200.00 ج.م.‏ 175.00

Bluetooth Module HC-06 , Serial TTL

03.00.33
Bluetooth UART RS232 serial converter Module Operating Frequency Band 2.4GHz unlicensed ISM band Bluetooth Specification V2.0+EDR Output Power Class 2 Operating Voltage 3.3V Host Interface USB/UART Audio Interface None Flash Memory Size 8Mbit. Features: CSR Bluetooth Chip Solution Bluetooth v2.0+EDR Compliant UART interface and with baud rate setup function Built-in antenna. Coverage up to 30ft. Incredible small size with 3.3V input, and RoHS Compliant Working current: While pairing 30mA, paired 8mA Frequency: 2.4GHz ISM band Baud rate is 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 user manually set up. Default Baud Rate: 9600,8,1,n Support for 8Mbit External Flash Onboard Support for 802.11 Co-Existence Product Description Storage Temperature: -40 to 85 degrees Celsius Size : 28 mm x 15 mm x 2.35 mm Used for GPS navigation system, water and electricity gas Automatic Reading Meter, The industrial field in control system The factory default parameters: Baud rate: 9600, N, 8, 1. Pairing code: 1234 AT command set as follows: 1, Test communication Send: AT (return OK, A seconds press once again) Return: OK 2, Change Bluetooth serial interface communication baud rate Send: AT + BAUD1 Return: OK1200 Send: AT + BAUD2 Return: OK2400 1---------1200 2---------2400 3---------4800 4---------9600 5---------19200 6---------38400 7---------57600 8---------115200 9---------230400 A---------460800 B---------921600 C---------1382400 Not recommended in more than 115200 baud rate, the signal interference will make the system not stability 3, change bluetooth name Send: AT + NAMEname Return: OKname Parameter name: will set the current name, which was the name of the search to Bluetooth. Within 20 characters. Example: send AT + NAME bill_gates Back to OKname now Bluetooth name is bill_gates Parameters can power lost save, modify it only need once. The PAD service can see change Bluetooth name 4, Change Bluetooth pairing password Send: AT + PINxxxx Return: OKsetpin Example: send AT + PIN8888 Back to OKsetpin now Bluetooth pairing password is 8888, module's default password g is 1234. Parameters can power lost save, modify it only need once.
ج.م.‏ 210.00 ج.م.‏ 185.00

DC to DC step down from 4-40V to 5V

03.00.30
Compatible with : Mobile Phones Brand : Asus Type : Battery Chargers
ج.م.‏ 120.00 ج.م.‏ 100.00

DC-DC Boost Converter (Mini) 0.9V ~ 5V T0 5Vdc/600mA

03.00.31
0.9V ~ 5V TO 5V 600mA USB Output Charger Step Up Power Module – MINI DC-DC boost Converter Specification Size: 24x18mm Output Current: Rated 0.6A Type: DC/DC Converters Input Voltage: 0.9 to 5 Vdc Output Voltage: 5.1-5.2 Vdc Weight: 0.03g Efficiency: Up to 96% Switching frequency: 500KHz Voltage indication: LED lights with load Operating Temperature: Industrial (-40 deg C to +85 deg C) Output: USB Output Product Description Module Properties: non-isolated step-up module (BOOST) Output Current: Rated 1A-1.5A (single lithium input), the maximum 1.5A (single lithium input) Voltage indication: LED lights with load (input voltage less than 2.7V LED indicator off) Full load temperature rise: 30 deg C Quiescent Current: 130uA Short circuit protection: None (Please use the lithium battery with protection.) Input Reverse Polarity Protection: None Connection: Welding Input: IN + Postive, IN-Negative – Output: USB Output
ج.م.‏ 50.00 ج.م.‏ 40.00

DC-DC Step Down Converter 4 Digital LED

03.00.60
Brand : Other Type : Microcontroller Boards
ج.م.‏ 225.00 ج.م.‏ 170.00

DC-DC Step Down Converter Variable 5A (5V..32Vdc to 0.8V..30Vdc)

03.00.57
OUTPUT VOLTAGE: 0.8V-30V INPUT VOLTAGE: 5V-32V OUTPUT CURRENT: ADJUSTABLE MAXIMUM 5A SIZE: 51 * 26.3 * 14 (L * W * H) (MM) OPERATING TEMPERATURE: -40 ℃ TO +85 ℃ VOLTAGE REGULATION: ± 2.5% LOAD REGULATION: ± 0.5% OUTPUT RIPPLE: 50MV (MAX) 20M BANDWIDTH SWITCHING FREQUENCY: 300KHZ CONVERSION EFFICIENCY: 95% (THE HIGHEST) RECTIFICATION: NON-SYNCHRONOUS RECTIFICATION MODULE PROPERTIES: NON-ISOLATED CONSTANT CURRENT AND VOLTAGE MODULE.
ج.م.‏ 130.00 ج.م.‏ 110.00

Dual H Bridge DC Stepper Motor Controller L298N Module for Arduino / Due and Raspberry Pi

03.00.25
Type : 3D Printer Accessories Brand : Other
ج.م.‏ 130.00 ج.م.‏ 100.00

Ethernet LAN Network Module ENC28J60 For Arduino SPI AVR PIC LPC STM32

03.00.22
Description: Chip board ENC28J60-I/SO. The board 25MHZ crystal. The network interface board HR911105A. 3.3 V power supply pin Specifications: Net weight:15 g Package weight:25 g Color:Blue Package Included: 1 x New ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC STM32
ج.م.‏ 150.00 ج.م.‏ 130.00

Heartbeat Sensor Module KY039

03.00.93
Brand : Other Type : Electronic Accessorie
ج.م.‏ 75.00 ج.م.‏ 60.00

High Power LED Module "Power 3W"

03.00.107
Color temperature: Warm White 3000-3200K / white 6000-6500K Forward current: 700MA Luminous flux: White 180-200LM (lumens) Forward voltage: 3.3 - 3.6 V Reverse voltage: 5V Power: 3W Viewing angle: 180° Working temperature: -20° to 60° Brand : Other
ج.م.‏ 45.00

HITSAN MKS-LV8729-OC Stepper Motor Driver Module High Subdivision One Piece

03.00.35
M CREATE A LV8729 MBASE MAKER (M), A SUPER QUIET REST, SUPPORTS EN +/-INPUT. MLV8729 DC SUPPLIES 9-32 VOLTS, AND GOOD FOR NIMA THE OTHER ENGINES THAT CURRENTLY HAVE LESS THAN 1.5 A. THESE CONTROLS MICROSTEP THE DRIVER BY THE CURRENT DIGITAL LOOP, MAKING THE ENGINE STATIONARY, QUIET AND ACCURATE. MLV8729 DOES GOOD WORK WITH THE GENERAL M, MSBASE AND RAMPS1.4 OBSERVER BOARD ON 3D PRINTER, MACHINE SCULPTING, CNC, ETC. FEATURES 1. DC 9-32 VOLTS, IT IS BETTER TO SUPPLY DC12V OR DC24V. 2. USE HIGH SPEED OPTOCOUPLER, DO NOT LOSE STEP. 3. USE THE SANYO LV8729, WHICH PROTECTS THE CIRCUIT AND SUPPORTS 128 MICROSTEP. 4. CURRENT MAX: 1.5 A. 5. MICROSTEP: 16/32/64/128. 6. GREATER HEAT SINK, BETTER COOLING. NOTICE 1. PLEASE MIND THE POLAR POWER, OR ELSE IT WILL BURN THE CHIP. 2. IT IS BETTER TO ADJUST THE CURRENT UNDER THE CURRENT CLASSIFICATION OF THE ENGINE, THE CURRENT ADVISES LESS THAN 1A. FOR THE MEGA2560 CONTROL, ADVICE NO MORE 64 MICROSTEP. 3. SWITCH1, 2 RECHARGEABLE MICROSTEP, SWITCH3, 4.5, USED FOR CURRENT, THE SWITCH6 ENTRY IS PLACED.
ج.م.‏ 250.00

Infrared Receiver Module KSM803

04.00.139
ج.م.‏ 30.00 ج.م.‏ 10.00

ISD1820 Voice Recording Recorder Module With Mic Sound Audio Loudspeaker Diy RC Toy Kit Electroincs Develop

03.00.36
Voice Recording MODULE Brand : Other Type : Microcontroller Boards
ج.م.‏ 75.00

KA2284 Power level indicator Battery Pro Audio level indicator module / arduino / raspberry pi

03.00.86
Features: 1. Chip: KA2284 2. Supply voltage: 3.5V-12V 3. The magnitude of the level can be adjusted 4. AC and DC signals can be controlled by jumper Package Contents: 1 X KA2284 Module
ج.م.‏ 100.00 ج.م.‏ 80.00

Laser Receiving Module

03.00.91
LASER RECEIVING MODULE
ج.م.‏ 100.00 ج.م.‏ 80.00

Laser sensor Module 650nm 6mm 5V 5mW Red Laser Dot Diode KY-008 for Arduino

03.00.90
LASER SENSOR MODULE 650NM 6MM 5V 5MW RED LASER DOT DIODE KY-008 FOR ARDUINO OPERATING VOLTAGE 5V POWER 5MW WAVELENGTH 650NM
ج.م.‏ 80.00 ج.م.‏ 60.00

LASER Source 5mW RED - DOT Shape

03.00.105
Operating Voltage: 3.00 ~ 4.00 Vdc Size 12mm Wavelength 650nm Power 5mW Dot Shape - RED Color Brand : Other Model Number : ledlm5689
ج.م.‏ 120.00 ج.م.‏ 100.00

Linear Hall Magnetic Module For Arduino AVR PIC

03.00.109
Linear Hall magnetic module and a digital interface, built-in 13 LED build a simple circuit to produce a magnetic field warning lamp 13 comes with digital interfaces of the LED, the linear Hall sensor magnetometer access number 3 interface, when linear Hall magnetometer Sensor senses a key signal, LED lights, otherwise off. Specs: Length: 42mm Width: 15mm Material: PCB
ج.م.‏ 80.00 ج.م.‏ 60.00

LM2596HVS DC to DC Adjustable Step Down Buck Converter Power Supply Module

03.00.24
Input voltage range: DC 4.5V to 53V (input voltage must be greater than the output voltage to 1.5V or more high. Could not boost)
ج.م.‏ 70.00

Micro SD Storage Board TF Card Reader Memory Shield Module SPI Port Arduino

03.00.100
Micro SD Storage Board TF Card Reader Memory Shield Module SPI Port for ArduinoProduct Details: Micro SD Card Module SPI interface via file system driver, microcontroller system to complete the MicroSD card reading and writing functions. Arduino users can use Arduino IDE comes with an SD card to complete the library card initialization and read-write directly. Power supply:4.5V ~ 5.5V, 3.3V ...
ج.م.‏ 60.00

Micro USB Interface Board With 5V Interface

03.00.104
Micro USB Interface Power Transfer Interface Breadboard 5V Power Module Development Board Size: 14 x 12 mm
ج.م.‏ 25.00

Motor Speed Control Switch Manual12Vdc to 40Vdc

03.00.27
MOTOR SPEED CONTROL SWITCH MANUAL 12V-40V 10A MODULATION PWM DC MOTOR SPEED CONTROL SWITCH GOVERNOR CONTROL THE SPEED OF A DC MOTOR WITH THIS CONTROLLER. HIGH EFFICIENCY, HIGH TORQUE, LOW HEAT GENERATING. WITH REVERSE POLARITY PROTECTION, HIGH CURRENT PROTECTION. WORKING VOLTAGE: DC 12V - DC 40V. CONTROL POWER:0.01 - 400W. STATIC CURRENT:0.02 A ( STANDBY ). PWM DUTY CYCLE:10% -100%. PWM FREQUENCY:13 KHZ. SIZE:6CM X 7.5CM X 2.8CM WEIGHT: 70G NOTE: THE WHITE CONNECTOR ON PCB TO EXTEND THE POTENTIOMETER 100K OHM WITH WIRE
ج.م.‏ 225.00 ج.م.‏ 195.00

Power Supply Module 3.3V 5V For Solderless Bread Board MB102

03.00.46
Brand : Other Type : 3D Printer Accessories
ج.م.‏ 50.00

Precision DS3231 Real Time Clock Module RTC

03.00.09
Brand : Other Type : Electronic Accessories
ج.م.‏ 85.00 ج.م.‏ 70.00

RC522 RFID Card Reader Module Kit for Arduino

03.00.34
THIS IS THE RFID 13.56 MHZ RFID MODULE BOARD KIT, THE MODULE BOARD THAT USED ON THIS KIT HAS RC522 INTEGRATED CIRCUIT THAT DRIVES THE 13.56 MHZ RADIO FREQUENCY. THE MF RC522 IS A HIGHLY INTEGRATED TRANSMISSION FOR CONTACT-LESS COMMUNICATION THAT RUNS ON 13.56 MHZ IT SUPPORT ALSO THE ISO 14443A/MIFARE MODE LIBRARY. THIS RFID KIT HAS INCLUDED THE S50 RFID CARD AND ID TAG.
ج.م.‏ 190.00

Relay Module 4 Channel

03.00.48
THIS IS A 5V 4-CHANNELS RELAY MODULE, IT CAN BE CONTROLLED DIRECTLY BY A WIDE RANGE OF MICROCONTROLLERS SUCH AS ARDUINO, AVR, PIC, ARM AND MSP430.
ج.م.‏ 100.00

Relay Module Two Channel

03.00.29
This is a 5V 2-Channels Relay module, It can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM and MSP430.2 relays are included in this module, with “NC” ports means “Normally connected to COM” and “NO” ports means “Normally open to COM”.This module is also equipped with 2 LEDS to show the status of relays.Maximum load: AC 250V/10A, DC 30V/10ADriving ...
ج.م.‏ 65.00

Serial Converter TTL UART on CP2102 USB Module Board

03.00.99
CP2102 its high integration, built-in USB2.0 full-speed function controller, USB transceiver, crystal oscillator, EEPROM, and asynchronous serial data bus (UART), supports full-featured modem signals, without any external USB device. CP2102 with other USB-UART adapter circuit works similar to the PC through the driver's USB port into a virtual COM port in order to achieve the purpose of expansion.
ج.م.‏ 95.00

Slide Type Switch Module 1-Bit 2.54mm 1 Position Way DIP Red Pitch

04.00.65
Slide Type Switch Module 1-Bit 2.54mm 1 Position Way DIP Red Pitch
ج.م.‏ 5.00

2 Position DIP Switch 2.54mm

04.00.66
Slide Type Switch Module 2.54mm 2 Position Way DIP Red Pitch DIP Package size and shape switch 2 Way , Suitable for digital inputs (High/Low) with very good materials.
ج.م.‏ 7.00

solid state relay 4 out put

03.00.37
Brand : Arduino Type : Electronic Accessories
ج.م.‏ 200.00

SSR-25DA 25 Amp 380V SOLID STATE RELAY FOTEK AC TO DC

03.00.79
SSR2DA IS AC TO DC SOLID STATE RELAY MODULE .25AMPS AND 380V FEATURESHighly reliable , compact size designed to offer users maximum simplicityDC to ACMounting method bolts fixedmade in Taiwan
ج.م.‏ 90.00

Stepper Motor Driver A3967 Module

03.00.53
Note: Do not connect or disconnect a motor while the driver is energized. This will cause permanent damage to the A3967 IC
ج.م.‏ 85.00

Stepper Motor Driver A4988 Module

03.00.07
LOW RDS ON TOTAL RESISTANCE BETWEEN THE DRAIN AND SOURCE OUTPUTAUTOMATIC CURRENT DECAY MODE DETECTION AND SELECTIONSYNCHRONOUS RECTIFICATION FOLLOW POWER DISSIPATIONINTERNAL UNDER VOLTAGE LOCKOUT UVLOCROSS CURRENT PROTECTION3.3 AND 5V COMPATIBLE LOGICSUPPLYTHERMAL SHUT DOWN CIRCUITRYGROUND FAULT PROTECTION LOAD SHORT CIRCUIT PROTECTIONOPTIONAL STEP FIVE MODES.
ج.م.‏ 65.00 ج.م.‏ 55.00

Stepper Motor Driver ULN2003 for Arduino AVR PIC

03.00.66
Brand: Other
ج.م.‏ 35.00